Dolphin Automotive Dual Rear View Parking Reversing Brake Light Camera - Wired

This dual lens brake light camera for vans/enclosed vans is a great secondary driving and reversing safety tool, one lens for driving and one lens for reversing. Especially for enclosed vans, you can't see the rear view through the rear view mirror, our monitor solves this problem, it's 6.86 inches, it's unique dual-screen display and single-screen switching, it's specially designed for dual-lens camera. Monitor button control instructions 1.Long-press the menu button for Video/System settings. 2.Long-press again to switch between them. 3.Single-click to confirm your selection. ♦♦Note: All dimensions are measured by hand and may allow some errors. Please Double Check the Bracket you need Features: Applicable to the following models： Reversing Camera for Mercedes Sprinter 2007 Onwards and VW Crafter 2007 - 2015 Dual lens brake light reversing camera,one lens can be used for long-term driving, and the other is used for reversing. 6.86" Dual-Screen Monitor: High-res (1280*480 IPS) display with dual inputs, 2 split screen, auto full-screen mode when reversing. ■ Dual Camera Wiring Guide(Please refer to the wiring diagram above) ■ Wire Functions Monitor wires: 1 ■ Red = +12V (Power +) 2 ■ Black = Power – (must go to the negative pole of the power supply, not vehicle chassis ground) 3 ■ Green = Reverse signal control Extension cable (short blue wires): 1 ■ Blue = Trigger wires (used for auto switching) DC power cable: 1 ■ Red = +12V 2 ■ Black = Power – Option 1: Both cameras work all the time 1 Leave all blue trigger wires and the green wire unconnected. 2 Connect both cameras’ DC power (red = +12V, black = –) to the ignition or accessory power. 3 ■ Both cameras stay on whenever the car is on. Option 2: One camera for driving (CH1), one for reversing (CH2) ■ CH2 (Reverse Camera – larger with IR lights) 1 Connect video output → AV2 input on monitor. 2 Connect one blue trigger wire → Green reverse control wire on monitor. 3 Connect the other blue trigger wire together with the red (+) DC wire → Brake light positive (+12V). 4 Connect black DC wire → Brake light negative (–). 5 ■ When reverse gear is engaged → Monitor switches to CH2 full screen with parking lines. ■ CH1 (Driving Camera – smaller camera on top) 1 Connect video output → AV1 input on monitor. 2 Leave AV1 trigger wire unconnected. 3 Connect red DC wire → Ignition power +12V (so it’s on while driving). 4 Connect black DC wire → Same negative as monitor/camera supply. 5 ■ This camera runs whenever ignition is on. ■ With this setup: 1 Normal driving →CH1 (drive camera) shows. 2 Reverse gear → Monitor automatically switches to CH2 (rear camera, full screen with parking lines). ■■ Important Notes 1 Do not connect any negative (black) wire directly to vehicle chassis ground — always return to the same negative pole of the power supply. 2 Wrap RCA connectors with electrical tape after plugging them in to prevent loosening from vibration. 3 Ensure all +12V feeds (ignition or brake light) are fused for safety Specification: Camera Specifications: Image sensor: 1/3" CMOS Lens: 2.8mm & 3.6mm Effective pixel: 1920(H)x720(V) Resolution: AHD 720P Night Vision distance: Approx.35ft Waterproof rating: IP68 Viewing angle: 90°&120° Video system: AHD S/N Ratio: > 48dB Current consumption: <150mA Minimum illumination: 0Lux(IR LED ON) Power: DC 12V Operating temperature: -20℃ to +70℃ Monitor Specifications: Material: ABS+glass Screen: 6.86 inch Resolution: 1280x(RGB)x480 IPS TV System: AHD Screen ratio: 16:9/4:3 adjustable Video Input: Dual video input Power Supply: DC 12V-24V Power consumption: 6W Blue screen on no signal Dual video inputs: Automatic full-screen switch during reversing Operation temperature: -20℃ ~ +60℃ Storage temperature: -20℃ ~ +60℃